Goal: Buck (cut) the stem into logs that maximize total value based on the AHMI grading matrix. Grade is determined by the small-end diameter and number of clear (defect-free) faces in each log.
- Click anywhere on the stem diagram to place a cut.
- Drag a cut marker left or right to reposition it.
- Right-click a cut marker to remove it.
- Roll Up / Roll Down (or arrow keys) rotates the stem so you can inspect all four faces for defects.
- Logs must meet a standard length (8, 10, 12, 14, or 16 ft) after subtracting trim allowance. Pieces too short to make 8 ft are waste.
- Diameter is measured at the small end of each nominal log length. A fractional part above .5" rounds up; .5" and below rounds down. The resulting whole-inch diameter is used for classification, reporting, and calculations in both your score and the optimal solution.
- Click Score This Stem to see your value, the optimal solution, and an explanation of any difference.
The Face Defect Map below the stem shows which faces each defect affects. Use it alongside the rotation view to decide where to cut.
Board-Foot Priced Products (priced by AHMI grade and Doyle board feet)
Prices for: General price list
| Small-End Dia. |
4 Faces |
3 Faces |
2 Faces |
1 Face |
0 Faces |
Grade and value are based on the rounded whole-inch small-end scaling diameter, clear faces, and Doyle board feet.
Scale deductions used in this trainer
- Sweep: measured for each candidate log as its maximum centerline departure from the chord between that log's ends. Cull when gross sweep is at least half the scaling diameter. Otherwise the trainer compares both AHMI deduction methods and uses whichever gives the higher sawlog value: 1 inch per full 4 inches of sweep from diameter, or 1 foot per full 3 inches from length.
- Crook: if its length is at least half the log length, treat it as sweep. Otherwise deduct 1 foot per full 3 feet of crook length. The AHMI guide also allows culling when crook length and displacement leave no acceptable lumber; that discretionary judgment is not modeled here.
- Interior defect (rot, hole, or decay): reduces scaling diameter by 1 inch for each full 3 inches of defect diameter.
- End check: reduces usable log length by the portion of the check inside the piece.
- Sector defect: reduces usable log length by its modeled sector deduction.
Sweep/crook deductions ignore fractions. AHMI allows the mill to choose either sweep rule; this trainer models the higher-value choice per sawlog for training and does not imply that mills should switch rules log by log.
Weight-Priced Products (sold by the green ton, not by grade)
Peeler $500/ton TESTING VALUE
- Species: Yellow-poplar, cucumber*
- DIB range: 8"โ28"
Weyerhaeuser Buckhannon, WV spec. Lengths: 9' (8'8"โ9'6"), 18' (17'8"โ18'6") โ culled if >1 ft over max or under min. Culled for forks, center rot/stain, splits >1 ft, sweep/crook >1/4 scaling diameter, or >10 knots per 9 ft of log. Yellow-Poplar weight uses the fitted peeler regression (diameter, length, butt/upper position).
Scragg ~$30/ton ($20โ$40 range)
- Species: Mixed hardwood, except pine/spruce/fir/basswood
- DIB range: 6"โ15"
#3/pallet grade (Silver Knob field spec). 7- or 8-ft multiples; no rot or splits; knots & moderate sweep tolerated, but no banana-shaped logs.
Value = log volume (cubic ft, from butt/top diameter & length) ร a per-ton conversion factor รท 2000
(or, for Yellow-Poplar peeler, a fitted weight regression instead).
Doyle board-foot scale is not used for these โ it underestimates real log volume, especially on smaller logs.
*Weyerhaeuser's spec also accepts Red Maple as Peeler โ not modeled in this tool yet.
Also not modeled: knots higher than 2" above the log surface, and metal (no data available for either).
Note: the Peeler price above ($500/ton) is a placeholder for testing only, so peeler bucking
choices actually show up in the optimizer โ the Weyerhaeuser sheet is not a price sheet, so
the real contract price isn't known here. Replace once a real price is available.
Training-price limitation: these values illustrate general bucking relationships only; they are not
a current species-specific, mill-specific, tract-specific, or live-market price schedule. Sawlogs use one shared grade-price table.
Each weight-priced product uses one flat per-ton rate (the Peeler rate is currently a testing placeholder). Usable volume is a major value driver, but weight-model inputs and product eligibility also matter.